 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by H11B1/D GlobalOptoisolatorTM H11B1 * [CTR = 500% Min] 6-Pin DIP Optoisolators Darlington Output (Low Input Current) The H11B1 and H11B3 devices consist of a gallium arsenide infrared emitting diode optically coupled to a monolithic silicon photodarlington detector. They are designed for use in applications requiring high output current (IC) at low LED input currents (IF). * High Sensitivity to Low Input Drive Current (IF = 1 mA) * To order devices that are tested and marked per VDE 0884 requirements, the suffix "V" must be included at end of part number. VDE 0884 is a test option. Applications * Appliances, Measuring Instruments * I/O Interfaces for Computers * Programmable Controllers * Interfacing and coupling systems of different potentials and impedances * Solid State Relays * Portable Electronics MAXIMUM RATINGS (TA = 25C unless otherwise noted) Rating INPUT LED Reverse Voltage Forward Current -- Continuous LED Power Dissipation @ TA = 25C with Negligible Power in Output Detector Derate above 25C OUTPUT DETECTOR Collector-Emitter Voltage Emitter-Base Voltage Collector-Base Voltage Collector Current -- Continuous Detector Power Dissipation @ TA = 25C with Negligible Power in Input LED Derate above 25C TOTAL DEVICE Isolation Surge Voltage(1) (Peak ac Voltage, 60 Hz, 1 sec Duration) Total Device Power Dissipation @ TA = 25C Derate above 25C Ambient Operating Temperature Range(2) Storage Temperature Range(2) VISO PD TA Tstg 7500 250 2.94 - 55 to +100 - 55 to +150 Vac(pk) mW mW/C C C VCEO VEBO VCBO IC PD 25 7 30 100 150 1.76 Volts Volts Volts mA mW mW/C VR IF PD 3 60 150 1.41 Volts mA mW mW/C Symbol Value Unit H11B3 [CTR = 100% Min] *Motorola Preferred Device STYLE 1 PLASTIC 6 1 STANDARD THRU HOLE CASE 730A-04 SCHEMATIC 1 2 3 NC 6 5 4 PIN 1. 2. 3. 4. 5. 6. LED ANODE LED CATHODE N.C. EMITTER COLLECTOR BASE Soldering Temperature (10 sec, 1/16 from case) TL 260 C 1. Isolation surge voltage is an internal device dielectric breakdown rating. 1. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. Preferred devices are Motorola recommended choices for future use and best overall value. GlobalOptoisolator is a trademark of Motorola, Inc. REV 1 (c)MotorolaInc. 1995 Motorola, Optoelectronics Device Data 1 H11B1 H11B3 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted)(1) Characteristic INPUT LED Forward Voltage (IF = 10 mA) Forward Voltage (IF = 50 mA) Reverse Leakage Current (VR = 3 V) Capacitance (V = 0 V, f = 1 MHz) OUTPUT DETECTOR Collector-Emitter Dark Current (VCE = 10 V) Collector-Emitter Breakdown Voltage (IC = 10 mA) Collector-Base Breakdown Voltage (IC = 100 A) Emitter-Collector Breakdown Voltage (IE = 100 A) DC Current Gain (IC = 5 mA, VCE = 5 V) (Typical Value) Collector-Emitter Capacitance (f = 1 MHz, VCE = 5 V) Collector-Base Capacitance (f = 1 MHz, VCB = 5 V) Emitter-Base Capacitance (f = 1 MHz, VEB = 5 V) COUPLED Output Collector Current (IF = 1 mA, VCE = 5 V) H11B1 H11B3 IC (CTR)(2) VCE(sat) ton toff tr tf VISO RISO CISO 5 (500) 1 (100) -- -- -- -- -- 7500 1011 -- -- -- 0.7 3.5 95 1 2 -- -- 0.2 -- -- 1 -- -- -- -- -- -- -- mA (%) Volts s s s s Vac(pk) pF ICEO V(BR)CEO V(BR)CBO V(BR)ECO hFE CCE CCB CEB -- 25 30 7 -- -- -- -- 5 80 100 -- 16K 4.9 6.3 3.8 100 -- -- -- -- -- -- -- nA Volts Volts Volts -- pF pF pF H11B1 H11B3 VF VF IR CJ -- -- -- -- 1.15 1.34 -- 18 1.5 1.5 10 -- Volts Volts A pF Symbol Min Typ(1) Max Unit Collector-Emitter Saturation Voltage (IC = 1 mA, IF = 1 mA) Turn-On Time (IF = 5 mA, VCC = 10 V, RL = 100 )(3) Turn-Off Time (IF = 5 mA, VCC = 10 V, RL = 100 )(3) Rise Time (IF = 5 mA, VCC = 10 V, RL = 100 )(3) Fall Time (IF = 5 mA, VCC = 10 V, RL = 100 )(3) Isolation Voltage (f = 60 Hz, t = 1 sec)(4) Isolation Resistance (V = 500 V)(4) Isolation Capacitance (V = 0 V, f = 1 MHz)(4) 1. 2. 3. 4. Always design to the specified minimum/maximum electrical limits (where applicable). Current Transfer Ratio (CTR) = IC/IF x 100%. For test circuit setup and waveforms, refer to Figure 11. For this test, Pins 1 and 2 are common, and Pins 4, 5 and 6 are common. TYPICAL CHARACTERISTICS 2 VF, FORWARD VOLTAGE (VOLTS) PULSE ONLY PULSE OR DC 1.8 I C , OUTPUT COLLECTOR CURRENT (NORMALIZED) 10 NORMALIZED TO: IF = 10 mA TA = 25C 1 1.6 1.4 TA = -55C 25C 100C 1 10 100 IF, LED FORWARD CURRENT (mA) 1000 1.2 1 0.1 TA = -55C THRU +25C +70C +100C 0.01 0.5 1 2 5 10 20 IF, LED INPUT CURRENT (mA) 50 Figure 1. LED Forward Voltage versus Forward Current Figure 2. Output Current versus Input Current 2 Motorola Optoelectronics Device Data I C , OUTPUT COLLECTOR CURRENT (NORMALIZED) H11B1 H11B3 10 7 5 NORMALIZED TO TA = 25C 2 1 0.7 0.5 0.2 0.1 -60 -40 -20 0 20 40 60 80 TA, AMBIENT TEMPERATURE (C) 100 140 IC, COLLECTOR CURRENT (mA) 120 IF = 10 mA 100 80 5 mA 60 40 20 0 0 1 2 mA 1 mA 2 3 4 5 6 7 8 9 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 10 Figure 3. Collector Current versus Collector-Emitter Voltage VCE , COLLECTOR-EMITTER VOLTAGE (NORMALIZED) Figure 4. Output Current versus Ambient Temperature ICEO, COLLECTOR-EMITTER DARK CURRENT (NORMALIZED) 105 104 103 102 10 1 0 20 40 60 80 TA, AMBIENT TEMPERATURE (C) 100 NORMALIZED TO: VCE = 10 V TA = 25C VCE = 30 V 10 V 1.3 1.2 1.1 1 NORMALIZED TO TA = 25C 0.9 0.8 0.7 -60 -40 -20 0 20 40 60 80 TA, AMBIENT TEMPERATURE (C) 100 Figure 5. Collector-Emitter Voltage versus Ambient Temperature Figure 6. Collector-Emitter Dark Current versus Ambient Temperature 1000 VCC = 10 V 1000 RL = 1000 100 100 10 10 t, TIME (s) 10 100 t, TIME (s) 100 RL = 1000 10 1 0.1 0.2 0.5 1 2 5 10 20 IF, LED INPUT CURRENT (mA) 50 100 1 0.1 0.2 0.5 VCC = 10 V 1 2 5 10 20 IF, LED INPUT CURRENT (mA) 50 100 Figure 7. Turn-On Switching Times (Typical Values) Figure 8. Turn-Off Switching Times (Typical Values) Motorola Optoelectronics Device Data 3 H11B1 H11B3 14 IC, TYPICAL COLLECTOR CURRENT (mA) 12 10 0.5 A 8 0.4 A 6 4 2 0 0 2 6 8 10 12 14 16 18 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 4 20 0.3 A 0.2 A 0.1 A 1 0.01 0.1 IF = 0 IB = 0.7 A C, CAPACITANCE (pF) 0.6 A 100 CLED f = 1 MHz 10 CCB CEB CCE 10 100 1 V, VOLTAGE (VOLTS) Figure 9. DC Current Gain (Detector Only) Figure 10. Capacitance versus Voltage TEST CIRCUIT VCC = 10 V RL = 100 IF = 5 mA INPUT OUTPUT 10% WAVEFORMS INPUT PULSE OUTPUT PULSE 90% tr ton tf toff Figure 11. Switching Time Test Circuit and Waveforms 4 Motorola Optoelectronics Device Data H11B1 H11B3 PACKAGE DIMENSIONS -A- 6 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. DIM A B C D E F G J K L M N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.300 BSC 0_ 15 _ 0.015 0.100 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 7.62 BSC 0_ 15 _ 0.38 2.54 -B- 1 3 F 4 PL N C L -T- SEATING PLANE K G J 6 PL 0.13 (0.005) TA M M E 6 PL D 6 PL 0.13 (0.005) M M TB M A M B M STYLE 1: PIN 1. 2. 3. 4. 5. 6. ANODE CATHODE NC EMITTER COLLECTOR BASE CASE 730A-04 ISSUE G -A- 6 1 4 -B- 3 S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.020 0.025 0.008 0.012 0.006 0.035 0.320 BSC 0.332 0.390 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.51 0.63 0.20 0.30 0.16 0.88 8.13 BSC 8.43 9.90 F 4 PL H C L -T- G E 6 PL D 6 PL 0.13 (0.005) M J K 6 PL 0.13 (0.005) TA M M SEATING PLANE TB M A M B M DIM A B C D E F G H J K L S CASE 730C-04 ISSUE D *Consult factory for leadform option availability Motorola Optoelectronics Device Data 5 H11B1 H11B3 -A- 6 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. DIM A B C D E F G J K L N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.400 0.425 0.015 0.040 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 10.16 10.80 0.38 1.02 -B- 1 3 F 4 PL N C L -T- SEATING PLANE G D 6 PL K 0.13 (0.005) M J TA M E 6 PL B M *Consult factory for leadform option availability CASE 730D-05 ISSUE D Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 6 Motorola Optoelectronics Device Data H11B1/D *H11B1/D* |
Price & Availability of H11B1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |